İçeriğe geç

How to Clean a Hydraulic Cylinder?

How to Clean a Hydraulic Cylinder?

How to Clean a Hydraulic Cylinder?

How to Clean a Hydraulic Cylinder?

Why Should a Hydraulic Cylinder Be Cleaned?

  1. Protecting Felt and Sealing Elements
  • Chips, dirt or rust particles remaining on the inner surface of the cylinder scratch the felts.
  • This leads to premature loss of tightness and oil leaks.
  1. Prevent Oil Pollution
  • When an uncleaned cylinder is installed in the system, the particles in it mix with the hydraulic oil.
  • Dirty oil  deteriorates valves, pumps and other sensitive elements in a short time.
  1. Prolong Working Life
  • Less wear → smooth lubrication → clean cylinder.
  • This extends the life of the cylinder and the system and reduces maintenance costs.
  1. Prevent Loss of Performance
  • Dirt and rust inside cause the piston rod to strain and disrupt the flow.
  • This reduces the power and speed performance of the cylinder.
  1. Prevent Corrosion
  • If moisture or foreign matter is not removed, corrosion begins on the inner surface.
  • This can lead to irreparable deterioration of the cylinder barrel.
  1. In terms of security
  • Hydraulic systems operate at high pressure (100–300 bar or even higher).
  • An uncleaned cylinder burst or oil leakage can cause serious work accidents.

Cleaning of hydraulic cylinders; It is  imperative for sealing, oil cleanliness, longevity, performance and safety.

  1. Exterior Surface Cleaning
  • The outer surface of the cylinder; It is cleaned of grease, dirt and dust.
  • A clean cloth + solvent-based cleaner (e.g. industrial degreaser) is used for this.
  • It  is dried with compressed air.
  • This step is very important to prevent dirt from entering the interior.
  1. Inner Surface Cleaning (Pipe Inner Diameter)
  • The inner surface of the hydraulic cylinder tube (barrel) should be cleaned if it contains scratches, rust or particles.
  • Methods used:
    • Honing Process → Removes scratches, makes the surface smooth.
    • Clean oil + flushing method → Drags out the sawdust, particles and dirt inside.
    • Wiping with cloth and solvent (in small cylinders).

Note: The inner surface should not be left dry. After cleaning, a thin oil film must be applied.

  1. Piston Rod Cleaning
  • If there is oil, dust or rust on the piston rod, it  is cleaned with a soft cloth and solvent.
  • Never  use sandpaper or wire brushes (the chrome plating will be damaged → the seals will wear out).
  1. Sealing Elements (Seals, O-rings)
  • The surfaces are cleaned before the seals are removed.
  • Old seals are discarded, new ones  are installed clean and lubricated.
  • No contaminants should come into contact during installation.
  1. Cleaning After Assembly
  • After the cylinder is closed, some filtered hydraulic oil is added to it  and it is moved back and forth several times by hand.
  • Thus, the remaining particles are expelled.
  • The cylinder  must be mounted on flushed lines before being connected  to the system.

Summary:
Hydraulic cylinder cleaning; It includes exterior wipe,  pipe inner surface honing or flushing, piston rod cleaning, seal renewal and lubrication steps. Purpose; to prevent damage to the seals, contamination of the oil and premature failures.

Hydraulic Cylinder Cleaning Procedure – Checklist

  1. Preparation
  • The cylinder is disengaged.
  • The work area has been made clean and dust-free.
  • Appropriate personal protective equipment (gloves, goggles, etc.) was worn.
  • Materials are ready: clean cloth, solvent/degreaser, compressed air, filtered hydraulic oil, new seals/O-rings.
  1. Exterior Surface Cleaning
  • The outer surface of the cylinder was wiped with solvent and cloth.
  • Oil and dirt are completely removed.
  • Drying was done with compressed air.
  1. Inner Surface (Cylinder Tube) Cleaning
  • The inner surface of the cylinder tube was visually inspected (are there any scratches, rust, particles?).
  •  If necessary, honing was carried out.
  • The inner surface is wiped with clean oil + cloth.
  • A thin film of oil was left on the inner surface (not left dry).
  1. Piston Rod Cleaning
  • The piston rod was wiped with solvent and a clean cloth.
  • A layer of rust, dirt or grease has been completely removed.
  • Scratch or chrome plating damage checked.
  • No sanders or wire brushes were used.
  1. Sealing Elements
  • Old seals and O-rings were dismantled.
  • Mattress surfaces have been cleaned.
  • The new seals were installed clean and lubricated.
  • No contaminants came into contact during assembly.
  1. Post-Assembly Controls
  •  After the cylinder was collected, some filtered hydraulic oil was added to it.
  • The piston rod was moved back and forth by hand and the inner surface was lubricated.
  • The grease and dirt remaining on the outer surface has been removed.
  • The cylinder was made ready to be mounted on flushed lines.
  1. Final Approval
  • The cylinder cleaning process is complete.
  • All parts were assembled completely.
  • The registration form was completed and entered into the maintenance report.

This procedure is a step-by-step guide for maintenance technicians  .